Designation: Graduate Assistant
Email: olusunmade.olusola@uam.edu.ng
Phone: (+234)7063474871
Gender: Male


Mr, Olusunmade, Olusola Femi, a lecturer of the Department of Mechanical Engineering, University of Agriculture, Markurdi, began his education Ife-Oluwa Primary School, Agege, where he obtained his Primary School Leaving Certificate and had his secondary education at Oniwaya High School, Agege where he obtained his WASSCE. He obtained the National Diploma (ND) in Mechanical Enhineering at Federal Polytechnic, Ilaro. He furthered his tertiary education by then obtaining a Bachelor of Science (B.Sc.) Degree and Master of Science (M.Sc.) Degree, both at Obafemi Awolowo University, Ile-Ife.


Mechanical Engineering Trainee
Fidson Health-Care Plc 2008
•Water treatment plant’s operation and servicing
•Steam generator’s operation and servicing
•Drugs processing and packaging (Encapsulation machine, Capsule polishing machine, Blistering machine, Rapid Mixer Granulator, Fluidized Bed Dryer, Mechanical sifter, Double cone blender, Tablet compression machine, Coating machine, Mono-Block Automatic Filling and Capping machine, etc )
Obafemi Awolowo University: Maintenance Division 2007
•Vehicle repairs and servicing
•Engine overhauling (water pump engine, Peugeot engine)
Universal Steels Limited: Enamel-ware Division2004
•Forming shapes from sheet metals
•Fork-Lift repairs and Servicing
•Vehicle repairs and servicing
•Refrigeration and Air-Conditioning
• Engine overhauling (CAT.12-Cylinder generator, Cummings 16-cylinder generator, CAT. fork-lift 4 and 6 Cylinders, etc)
•Water pump servicing
• Compressor servicing (Atlas Copco)
Jerry Foam Nigeria Limited2003
•Foam making and processing (Crumbling machine, Cutting machine, etc)


Master of Science (M.Sc.) Degree in Mechanical Engineering2015
Graduated with Distinction
Obafemi Awolowo University Ile-Ife
Bachelor of Science (B.Sc.) Degree in Mechanical Engineering2010
Second Class Honour (upper division)
CGPA of 4.37 out of 5.0
Obafemi Awolowo University Ile-Ife
National Diploma (ND) in Mechanical Engineering 2004
Graduated with Distinction
CGPA of 3.56 out of 4.0
Federal Polytechnic Ilaro

Oniwaya High School Agege

Primary School Leaving Certificate1995
Ife-Oluwa Primary School Agege


Programming and software development (VB.Net), picture editing (Photoshop), desktop publishing, internet appreciation and multi-media content development


Mechanical Engineer; Council for the Regulation of Engineering in Nigeria (COREN), R382842017

Corporate Member; Nigerian Society of Engineers (NSE), 40319


Journal Articles
Olusunmade Olusola Femi, Bulus Abba Emmanuel and Kashin Terwase Kelvin (2018): Effect of imperata cylindrica (IC) reinforcement form on the tensile and impact properties of its composites with recycled low density polyethylene (RLDPE), Journal of Advanced Engineering, ACTA Polytechnica.
Ogunnigbo C. O., Adetan D. A. and Olusunmade, O. F. (2018): Assessment of a Modified Mixer in wet Dehulling of Cowpea (Vigna unguiculata), Agricultural Engineering International: CIGR Journal, China.
Olusunmade Olusola Femi, Zechariah Sunday and Yusuf Taofeek Ayotunde (2018): Characterization of Recycled Linear Density Polyethylene-Imperata Cylindrica Particulate Composites, Journal of Advanced Engineering, ACTA Polytechnica.
Ogunnigbo C. O., Adetan D. A. and Olusunmade, O. F. (2018): Effect of soaking time on some engineering properties of cowpea (Vigna unguiculata), Agricultural Engineering International: CIGR Journal, China.
Olusunmade Olusola Femi, Adetan Dare Aderibigbe and Ogunnigbo Charles Olawale (2016): A Study on the Mechanical Properties of Oil Palm Mesocarp Fibre Reinforced Thermoplastic, Journal of Composites, Hindawi Publishing Corporation.


Mechanical Engineering

Research Archive

Sustainable management of municipal solid and bio wastes. Conversion of thermoplastic and synthetic rubber wastes to construction materials and energy. Bio-fuel and cutting fluid production from agricultural wastes


University of Agriculture Makurdi: Department Of Mechanical Engineering
•Teaching undergraduate courses: system dynamics and acoustics, tool and jig design, machine tool engineering and engineering workshop practice
•Supervision of undergraduate and postgraduate diploma students (9 completed; 6 on-going)